关于TinTin的流水帐 （七）
作者:爱吃的妈妈 日期:2009-11-25
FN 公司的一组宣传图
作者:黄敏 日期:2009-11-23
繁忙的周末：装屋顶排气扇，修水龙头，换纱窗，换拉门的滚轮
作者:黄敏 日期:2009-11-20
于是周五晚上跑到bunnings一气买了下列东西，准备周末做完：
给vent
How to Replace the Rollers on your Patio Door
作者:黄敏 日期:2009-11-20
Every time we go out our sliding glass door and hear that grinding under the rollers, and have to use excessive force to open it, we say to our selves, "I'm gonna fix that one of these days"! But then we realize, "HOW"? Well, it's really quite simple, but there are a few tricks; so let's get started.
Things You'll Need:
- Long shafted phillips screw driver,large tip.
- regular phillips screw driver
- WD-40 or equivalent.
- tooth picks
- paper towels
- old tooth brush
- metal dental pick
- pry bar
-
Step 1
Removing the door panel: On a sunny day with mild temperatures, purpose to "fix that sucker", and do it expediently. Sliding glass doors are heavy and awkward, so get some help to remove the panels if you need. Usually, the operable panel of a sliding glass door will come out on the inside of the structure. Sometimes there will be sag in the header above the unit, so it may be necessary to remove the fixed panel from the outside first. Take your small Phillips screw driver and find the roller adjustment holes at the bottom of the door. Insert the tool into the hole and engage the roller screw. Lower the door down as much as possible, by doing forward and back rollers. Now try to lift the door up and swing the bottom into the room to remove the door.
-
Step 2
Removing the old rollerRemoving the rollers: Rest your door on it's edge, and locate the roller adjustment hole. JUST ABOVE that hole is another hole. This is the hole that has a frame/roller screw in it. You must completely remove this screw to remove the old roller.( Be careful not to separate the frame from the glass when doing this procedure)Use the large Phillips screw driver to remove this screw. Pry out the old roller. Secure the door.
-
Step 3
Like for LikeTags: fix roller sliding_door
How to Install an Attic Vent
作者:黄敏 日期:2009-11-18
Good Video: roof vent: www.youtube.com/watch eave vent: www.youtube.com/watch
Tags: attic roof vent ventilation
How to replace Flyscreen Mesh
作者:黄敏 日期:2009-11-16
How to replace Flyscreen Mesh
This handyman hint explains how to replace the mesh in a flyscreen door.
To replace the mesh in your flyscreen doors and windows, start by measuring the height then the width of the flyscreen you wish to replace. You will need a minimum of 75mm to 100mm (3 to 4 inches) extra all round. Write these measurements down and take them to your local hardware store. Meshing is sold in widths of 900mm (about 3 feet) and 1200mm (about 4 feet).
When you get home again, remove the screen by lifting and then twisting one corner out, then slide the screen out completely. Remove the rubber tubing that holds the mesh into the frame by prying up at the join, pull gently until it comes free. Now you can remove the old mesh and dispose of in the rubbish bin.
Lay the new mesh over the screen door and then push the rubber tubing into the slot at one corner, on the longest side of your screen. You can purchase a wheel at the hardware store for this job. Alternatively, you can use a small piece of timber dowel or the handle of an old dinner knife with a very blunt blade. Holding it at an angle to the mesh and apply downward pressure.
Tags: fly_screen
